Recent content by mafify

I removed the Battery CAN ID's and added a separate delays on all other reported msgs. I can confirm that the 40 kWh SOC got updated but the 62 kWh didn't update. I am not sure if it might be a BMS issue from the Pack itself. I will see if I can find another 62 kWh anywhere

Thank you so much! I was logging in today to tell you I brought a ZE1 model to collect some data and try out, but you already have it here! I will try them out and let you know for sure. Thank you again!

so, it's another CAN interface from the charger to the BMS, So I need another CAN interface to flow data in these two pins to get updates than :idea:

Another question too :D . So I only have the +IGN and the +12 to power the BMS. 3 relays which is Neg, Pos, Pre and 1 ground. last is the CAN H and CAN L. To charge and discharge the battery, there is a high terminal connected to the system that discharge and charge the battery. I can't use...

So a quick recap, I have 24, 30, 40 and 62 kWh packs. when I send the 50B wake up signal , I can make SOC updates on only 24 and 30 kWh. It failed on the 40 and 62 kWh and I both backs are a ZE1 2018+ model Also, for me to see the SOC update, I have a discharge and charge system at 20 Amp which...

New Update: I got it updating also on the 30 kWh pack. But the 40/62 kWh didn't.

Another Update. The Gen 1 pack "24 kWh" responded to the 50C and 50B msgs and updated the SOC but the gen 2 packs didn't take the 50C and 50B. I figured out that the 50C msg in your log was actually changing the msg 55B "LB_ALU_ANSWER" between 55 and AA

I am getting the 55B messages from the BMS already, but it doesn't update. That is my main issue. Tried to send 50B, 1F2, 1D4, 11A and 50C. What I think is there is a certain msg from the VCM that keep the BMS updating values Only worked on the 24kWh but no response from the AZE01 30,40 and...

Curious question :D , The SOC is updating on the battery standalone? :shock:

Thank you for the follow up. Yes, I am following the 100 ms and 10 ms period for the msgs. Also make sure about the EPRUN, CSUM and CRC. Just to clarify, I am testing on 4 different packs 24, 30, 40, 62 kWh batteries. I will take a look again on my code if I have any mistake in the calculations...

I just ran all the VCM ID at the same time, I can see a change in ID 55B for the first time in the LB_ALU_ANSWER but SOC is still static. I will try to discharge and see if SOC start to change.

Hello, I am also trying to Awake the SOC on gen 2. Nothing is successful yet only running the 50B. 50C and 1F2 msgs but no hope till now. I am also following Dala suggestions. But I feel I am so near to get it working

I did many tests in hope to bring the interlook, SOC Awake to refuse to sleep to get the SOC updates it's value First I sent 50B as a static message: 50b#000006C0000000 I am also sending the 1F2 to make sure it's in normal charge mode and Keep SOC is on with making sure that my CSUM and EPRUN...

I will test this out tomorrow and come back to you with the results! Thank you for the feedback :D

I am actually sending the 50B ID as a static msg "000006c0000000" every 100 ms, which mentioned in your excel. I am also following the relay sequence and I can charge and discharge smoothly. But still SOC doesn't update