ChicagoLeaf
Posts: 2
Joined: Sun Jul 29, 2018 5:51 pm
Delivery Date: 30 Jul 2018
Leaf Number: 321267
Location: Chicagoland

Re: Aftermarket & OEM Accessories for 2018 Leaf

Mon Dec 10, 2018 11:20 am

LeftieBiker wrote:I have a cargo net from either my previous Leaf (likely) or my housemate's PIP. It appears to fit between the mounting points in my 2018 SL. Do I need different push pins to hold it, or will the existing ones work? I don't want to mess around and break them. Is there a source for the pins with hooks if that is what is needed?
I moved my cargo net (and two pins) from my 2015 to 2018 LEAF--seems to function as expected.

LeftieBiker
Moderator
Posts: 12992
Joined: Wed May 22, 2013 3:17 am
Delivery Date: 30 Apr 2018
Location: Upstate New York, US

Re: Aftermarket & OEM Accessories for 2018 Leaf

Mon Dec 10, 2018 12:04 pm

Anyone have a source for the pins? I wonder how much the new part for the older Leafs cost.
Scarlet Ember 2018 Leaf SL W/ Pro Pilot
2009 Vectrix VX-1 W/18 Leaf modules, & 3 EZIP E-bicycles.
BAFX OBDII Dongle
PLEASE don't PM me with Leaf questions. Just post in the topic that seems most appropriate.

LeftieBiker
Moderator
Posts: 12992
Joined: Wed May 22, 2013 3:17 am
Delivery Date: 30 Apr 2018
Location: Upstate New York, US

Re: Aftermarket & OEM Accessories for 2018 Leaf

Wed Dec 12, 2018 4:51 am

The Weathertech floor mats are a mixed fit. They seem to have left them unchanged from the Gen I Leaf, and while the driver's side fits perfectly, the passenger side doesn't. There is a gap between the "mat" and right outer side of the footwell that can catch a passenger's foot entering or leaving the car. I may try to reshape it with a heat gun. I got front only mats, saving about $75, and reused the Weathertech universal rear mats from my 2013 Leaf.
Scarlet Ember 2018 Leaf SL W/ Pro Pilot
2009 Vectrix VX-1 W/18 Leaf modules, & 3 EZIP E-bicycles.
BAFX OBDII Dongle
PLEASE don't PM me with Leaf questions. Just post in the topic that seems most appropriate.

LeftieBiker
Moderator
Posts: 12992
Joined: Wed May 22, 2013 3:17 am
Delivery Date: 30 Apr 2018
Location: Upstate New York, US

Re: Aftermarket & OEM Accessories for 2018 Leaf

Wed Oct 09, 2019 9:23 pm

I recently acquired a front seat set of slightly used Coverking seat covers. No one seems to have made new covers for the 2018 Leaf, even though the Tech package adds a power driver's seat, and I was reluctant to pay $200+ for two seat covers that might not fit well. Tonight I installed them...

First, the Bad News: the power seat is not only not a great fit for the cover, but installation as designed is virtually impossible. Why? Because the Coverking covers (and I assume other brands as well) are designed with rear to front straps that fasten underneath the seats. There is not enough room beneath the Leaf power driver's seat to reach under and fasten strap buckles. There is barely enough room to fish the straps out under the seat backs, and the installation tool they provide is too short (as are the straps) to fish them to the very front of the seat. After wasting most of an hour trying, I finally used insulated wire to just connect the front and rear buckles. This is unsatisfactory both because it's crude, and because with no elastic in the straps, it doesn't properly tension the cover either. I will eventually replace the wire with elastic cord.

Now the good news: the passenger seat cover fits much better, although as with the driver's seat cover I ended up fastening the side straps to the lower rear straps, tucking them below the seat hinge covers. It looks better than the cheap universal covers I had on the seats, but you can still see that the covers aren't a perfect fit on the lower seat cushions.

This is just Odd: if you install the headrest covers so the gray stripe matches the stripes on the seats, they don't fit well at all - the areas that wrap the headrest support rods are in the wrong places. They only fit ok (not great) if you reverse them, putting the gray facing the back seats. I don't mind the black headrests, as my 2013 had them. Anyway, I'll add pictures one of these days...
Scarlet Ember 2018 Leaf SL W/ Pro Pilot
2009 Vectrix VX-1 W/18 Leaf modules, & 3 EZIP E-bicycles.
BAFX OBDII Dongle
PLEASE don't PM me with Leaf questions. Just post in the topic that seems most appropriate.

Return to “Accessories / Mods”