Leaf Spy and Leaf Spy Pro

[DaveinOlyWA]

since the last update both my ahr and health have stayed the same. not sure if i should be concerned about a possible bug or be happy that my pack has reached a point of stability for the first time since i got the app?

To address this concern and insure we are always looking at fresh data I am adding a change to the code.

When first connecting to the Leaf (reading VIN) the app will now clear to zero AHr, SOH, SOC and Hx. So when you see a non-zero value you will know it was just read from the Leaf and is not old saved data.

ok hate to beat a dead horse (unless I am hungry and there is no cow around...) but I did finally see changes in the ahr and health readings. they bounced around a few days and now its stuck on 57.11 ahr and 74.18 health for the past several days.

i even update SW this morning to the latest and still no change. its been static for like 5-6 days now

so wondering; is anyone else seeing steady readings like this? because before I was seeing changes nearly every time i powered up the car.

[patrick0101]

is anyone else seeing steady readings like this? because before I was seeing changes nearly every time i powered up the car.

My SOH is stuck at 86%. I assumed it is because the decimal place values are no longer reported. Ah and Hx are still wiggling about normally.

[Turbo3]

is anyone else seeing steady readings like this? because before I was seeing changes nearly every time i powered up the car.

My SOH is stuck at 86%. I assumed it is because the decimal place values are no longer reported. Ah and Hx are still wiggling about normally.

SOH is only available as an integer so no decimal places to show.

[palmermd]

... Lots of small fixes plus DTC clearing for the PRO version.

Did not have time to validate the DTC clearing the away I wanted too but I needed to get all the fixes out. So post any issues with DTC Clearing and I will fix them in the next release.

I have adjusted the height of the progress bar so that it will not extend down into the list of DTCs. It will be in the next release.

Is that the problem you are seeing on your tablet?

I think so. I only went through the sequence once, but I just remembered that something existing on the screen got partially overlapped by the progress bar and then the bar went away once it was done. I'll try again later tonight to see for sure.

Sorry I did not get back on this issue. My cheap tablet seems to have died and I cannot recover it, so I'll have to go purchase a new device before I can get online with my Leaf again....z

[patrick0101]

SOH is only available as an integer so no decimal places to show.

Prior to November 14th (sorry I didn't note the app version), SOH was being displayed in the app with 2 decimal places. Were these last two digits just random data?

[TickTock]

SOH is only available as an integer so no decimal places to show.

Prior to November 14th (sorry I didn't note the app version), SOH was being displayed in the app with 2 decimal places. Were these last two digits just random data?

That was a derived value based on Ah/XXX. The new SOH is the SOH reported by the Leaf to the dealer test equipment (which also appears to be very close to Ah/YYY) but the Leaf only reports an integer. If you want to monitor the day to day fluctuations, the Ah readout will give the same information (just not normalized).

[patrick0101]

That was a derived value based on Ah/XXX. The new SOH is the SOH reported by the Leaf ...

Thanks again for dispelling my ignorance. I missed that in the change logs.

[Turbo3]

SOH is only available as an integer so no decimal places to show.

Prior to November 14th (sorry I didn't note the app version), SOH was being displayed in the app with 2 decimal places. Were these last two digits just random data?

There was no SOH before Novermber 14th. Back then the top line showed something like this:

Bat Sts: AHr=56.53 (86.17%) Hlth= 82.60%

The 86.17% is just AHr divided by a constant of 65.6. Although you could change the constant in settings. The Hlth number is from the Leaf and is now called Hx. SOH is a brand new value that was found (TickTock?).

[DaveinOlyWA]

is anyone else seeing steady readings like this? because before I was seeing changes nearly every time i powered up the car.

My SOH is stuck at 86%. I assumed it is because the decimal place values are no longer reported. Ah and Hx are still wiggling about normally.

oh sorry, my bad. old habits die hard. i meant to say Hx (or old "health") but i am now convinced that i simply have a very stable pack. I did a reset on the log file, logged off and back on and the SOH did reset briefly to zero before displaying a new number and... ahr and Hx still did not change. so have to say... i'm just real stable right now

[TimeHorse]

As a general rule, I try to read every post in a thread before posting myself, mainly to make sure I don't retread any ground. I did cheat a bit with the LEAF Spy Lite forum; I read that one completely last week but was still working on this one. But now I'm caught up, hooray!

So excellent work Turbo and one of these days I hope you'll trust me to take a peak at the code inside to see if my Jailbroken iPhone can have a version of the app, but that's a whole 'nother can of worms. And we all know the green worms go towards the green glass.

Anyway, so let me try a tyre pressure request redux. Rather than the "car" glyph I suggested earlier, how hard would it be to add an arrow to the 4 tyre pressure gauges such that the arrow always points to the front of the car. So to the left of the point of the arrow is Front-Left, etc. This shouldn't be too hard to do and would help with the confusion I get between landscape and portrait orientation.

Anyway, well done sir and I'm very happy I bought both versions because that means you get paid twice and all that it's still not enough to say thanks!