2013 SV, no QC, no LED, with Nav.enrohT5 wrote:Chiv,
Which SV features do you have? QC, LED, Nav?
Planning on using the OEM backup camera?chivalryx wrote:2013 SV, no QC, no LED, with Nav.enrohT5 wrote:Chiv,
Which SV features do you have? QC, LED, Nav?
I bought a harness adapter, but it hasn't arrived yet. Will report back once I give it a try, and once I confirm the pins are correct. FYI in the service manual, it's around page 128 in the Navigation section where you get the pin layout.![]()
http://www.ebay.ca/itm/152050490325?_tr ... EBIDX%3AIT
Chiv.
Assuming the pins are correct, you should be able to splice the wires to the harness wires, saving the step of adding pins/wires. At worst I dismantle it, steal the pins, solder the wiring from the camera to the pins, and put the pins directly into the original connector.vashwood wrote:Planning on using the OEM backup camera?chivalryx wrote:2013 SV, no QC, no LED, with Nav.enrohT5 wrote:Chiv,
Which SV features do you have? QC, LED, Nav?
I bought a harness adapter, but it hasn't arrived yet. Will report back once I give it a try, and once I confirm the pins are correct. FYI in the service manual, it's around page 128 in the Navigation section where you get the pin layout.![]()
http://www.ebay.ca/itm/152050490325?_tr ... EBIDX%3AIT
Chiv.
Sounds like a plan. Let me know how it turns out.chivalryx wrote:Assuming the pins are correct, you should be able to splice the wires to the harness wires, saving the step of adding pins/wires. At worst I dismantle it, steal the pins, solder the wiring from the camera to the pins, and put the pins directly into the original connector.vashwood wrote:Planning on using the OEM backup camera?chivalryx wrote:
2013 SV, no QC, no LED, with Nav.
I bought a harness adapter, but it hasn't arrived yet. Will report back once I give it a try, and once I confirm the pins are correct. FYI in the service manual, it's around page 128 in the Navigation section where you get the pin layout.![]()
http://www.ebay.ca/itm/152050490325?_tr ... EBIDX%3AIT
Chiv.
Worth a try anyways
So end result, the harness is no good for an SV, it's only good for an S with the smaller display (4.3"). I dismantled the harness to harvest the pins, plugged them into where I was missing wires on the NAV connector, and the aftermarket camera works!vashwood wrote:Sounds like a plan. Let me know how it turns out.chivalryx wrote:Assuming the pins are correct, you should be able to splice the wires to the harness wires, saving the step of adding pins/wires. At worst I dismantle it, steal the pins, solder the wiring from the camera to the pins, and put the pins directly into the original connector.vashwood wrote:
Planning on using the OEM backup camera?
Worth a try anyways
What aftermarket camera did you use? Were you able to fit it in the OEM Leaf Camera housing?chivalryx wrote:So end result, the harness is no good for an SV, it's only good for an S with the smaller display (4.3"). I dismantled the harness to harvest the pins, plugged them into where I was missing wires on the NAV connector, and the aftermarket camera works!vashwood wrote:Sounds like a plan. Let me know how it turns out.chivalryx wrote:
Assuming the pins are correct, you should be able to splice the wires to the harness wires, saving the step of adding pins/wires. At worst I dismantle it, steal the pins, solder the wiring from the camera to the pins, and put the pins directly into the original connector.
Worth a try anyways
Pin#40 - Camera Image Signal (video wire)
Pin#60 - Camera Image Signal Shield
Pin#58 - Camera Sense (connect to chassis to ground)
Essentially wire it the same as the "Bose" wiring pins in the service manual.
So if you went to the OEM, all you now need is to figure out which wire sends 6.2V for the camera and you're set.
Expensive way to get the pins though, you might need to find somewhere else that sells just the pins and solder the wiring yourself.
Chiv.
It was just a cheap camera from China to test the wiring was correct. I didn't want to buy all the OEM parts just to find out it was impossible to get working! Now that I have that sorted out, I can pick up the correct parts (Hatch handle and camera).vashwood wrote:
What aftermarket camera did you use? Were you able to fit it in the OEM Leaf Camera housing?